NebraskaPeteGeek

Tag: “ “ “Kaywoodie Hand Made ”

A Kaywoodie HandMade Saddle Stem Restoration

March 1st, 2024

Photographed and written by

John M. Young

I am starting to feel like I work at a lumber yard. This is the third Kaywoodie HandMade restored in the past couple of weeks. Good thing they are fun to work on. The first one had a push stem and no Kaywoodie logo on the stem. The second was a tapered stem with a white circle with a black 3 leaf clover logo. This one is all decked out with a saddle stem and the same white and black logo as the tapered stem. That logo was discontinued after 1955, according to pipedia.org and the shape first appeared in the 1947 catalog.

I’m just going to copy the historical information from the first HandMade restoration.. I am pretty sure that nothing historical has changed in the last few days.“Kaywoodie name first appearing in February of 1919.” (Kaywoodie History – Greywoodie LLC) The history of Kaywoodie pipes is fortunately well documented thus, allowing rather precise dates for a Kaywoodie collector to declare the provenance of their charges. The above pictured Kaywoodie is stamped HANDMADE over KAYWOODIE (left) and IMPORTED BRIAR (right). No shape number is present.

Using this information and referring to the Kaywoodie Collectors’ Guide listed on pipedia.org I found that these pipes were made during the following years:

“Handmade-Oversize-Carved 1947-1955 on and off” (https://pipedia.org/images/3/3d/Kaywoodie_Pipe_Names.pdf) and that

“The Oversize Kaywoodies were, as the name implies, “Giants”. Lowndes notes that these pipes were stamped simply, “Hand-Made”. The pipes were all roughly “bulldogish” in appearance and were available in the following styles and grades7 : • Hand-carved “Colossus” ($10) • Walnut finish, banded “Hercules” ($20) • Hand-carved “John Henry” ($10) • Virgin finish, specimen grain “Paul Bunyan” • ($25)Virgin finish, banded specimen grain “Goliath” • ($25)Walnut finish “Atlas” • ($20)Hand-carved, Meerschaum-Inlaid “Samson” ($15)” (Kaywoodie Collector’s Guide – p10.pdf)

Looking into the stampings, I went to piphil.eu for confirmation. ThereI was able to find an exact match of this pipe’s stampings.

(Kaywoodie series from L to Z — Pipes : Logos & Markings (pipephil.eu))

Well, that was easy. This large Kaywoodie Hand Made, though not very “bulldogish” was most likely made between 1947 and 1955 at the West New York, New Jersey factory. If you would like to see the 1947 Kaywoodie catalog here is a link: Kaywoodie_1947.pdf (pipedia.org). It is a fascinating read with great old marketing photos and illustrations. Just out of curiosity I wondered what $10 in 1947 was equivalent to today. According to a bis.gov inflation calculator it is $131.09 (Using Dec. 1947 and Dec. 2023)(CPI Inflation Calculator (bls.gov)). I highly recommend reading the above links for further Kaywoodie history.

This Kaywoodie HandMade saddle stem came from Las Vegas Nevada to southeast Nebraska. All three Kaywoodie HandMades were from the same seller. The first one bought on a whim the second two were negotiated for. I will link the first two restorations for you, if you are interested in reading about them: Hand Made 1 and HandMade 2. This third pipe was stamped HANDMADE over KAYWOODIE on the left shank and IMPORTED BRIAR on the right. No stampings were on the bottom. Below are photos of how the pipe appeared upon arrival.

This restoration began like most others with a fresh clean denim piece for the work surface. I should show the final version of the denim, I’ll probably forget but it’s worth a shot.

Since this stem was badly oxidized I decided to give it a several hour long soaking in the Before and After Deoxidizing Solution. I first sanded the stem with a 400 grit sanding sponge and cleaned out the interior with several alcohol dipped bristle pipe cleaners. The final pipe cleaner You see in the photo above, inserted into the stinger.

The stem was too long to hang in the solution. I ended up using a wood sanding block to tilt the jar of Deoxidizing solution (deox, as I like to call it).

It wasn’t perfect but I was certain that it would work. At this point I actually went upstairs to type up the restoration of the second Kaywoodie HandMade. Oh, this is confusing. About 4 hours later, I returned to the deox jar to retrieve the stem. After allowing most of the excess solution to drip off the stem, I like to use a coarse cotton shop rag to vigorously rub off the remaining solution.

The stem looked much better. You can see the black has returned but the surface was rough and pitted.

I used Soft Scrub on make-up pads to rub off the remaining oxidized vulcanite.

After the Soft Scrub I oiled the stem with a coating of mineral oil and allowed it to soak up the oil while I started work on the stummel.

Looking back at my photos I apparently neglected to photograph the reaming of this HandMade. Don’t worry, you are not missing much. This pipe had been smoked very little as you will see when I describe the shank cleaning. The reaming was very quick and uneventful. I used the PipNet with the #3 blades to barely mess up my plastic drop surface. The scraper and knife were not used and the tobacco chamber was sanded with 220 sandpaper on a wood dowel followed by 320 sandpaper wrapped around a Sharpie marker. The most interesting part was that there was a shallow groove inside the chamber that ran along the left side. I remembered that the second Kaywoodie HandMade also had a groove in it’s chamber. Upon looking very closely at both with a bright flashlight I saw what appeared to be a thin crack in both chambers. It did not go from the top to the bottom; rather it was about ½ to ¾ inches long in the center of the chamber on both pipes. It almost looked like it was a crack from improper drying or the chamber was bored out while the wood was not completely dried. I then remembered that both of these pipes had come from Las Vegas Nevada, a place not known for their humidity. Perhaps years of storage in the desert had not been good for the pipes. Either way I thought it would be best to mix up some J.B. Weld and fill the crack from within the chamber. Allow the epoxy to set and sand it smooth with the chamber surface. I thought that I would come back to do that step with both pipes when I was finished with the restoration.

I took the stummel to the sink. There I scrubbed the stummel with undiluted Murphy’s Oil Soap and a medium bristle toothbrush. The years of dirt and grime were evident in the lather. The stummel was rinsed in warm water and dried with a cotton dish towel.

When finished drying I poured 5 ml of 95% ethyl alcohol into the tobacco chamber and allowed it to flow into the shank. Without pouring the alcohol out I used a nylon shank brush to scrub the airway within the shank with the alcohol. This alcohol was poured into a medicine cup. The color indicated the extent of the tar accumulation in the airway.

THe very light color of the alcohol led me to believe the shank was relatively clean. A few alcohol dipped cotton swabs confirmed this.

With the internals cleaned out I returned to the exterior of the stummel. There seemed to be some yuck (the technical term for unwanted debris) in the grooves of the carvings. I wetted a make-up pad with 95% ethyl alcohol and wiped-down the exterior of the stummel. Very little color came off.

I then used a stiff nylon bristle brush dipped in the alcohol to scrub the carvings. Again I wetted a make-up pad and wiped the surface. This time the grooves looked deyuckified and it showed on the make-up pad.

The rim looked very clean after the alcohol and nylon brush scrubbing. Although it did show a bit of charring around the inside edge of the rim.

Now to deal with that charring. I used a wood sphere with a piece of 220 sandpaper. The sphere provided an even angle for a bevel and erased the charred briar. THe bevel was then sanded smooth with the sanding sponges by using the 400, 1000, 1500 and 2500 sponges in sequence.

The stummel required no real sanding other than a light buff with the previously mentioned sanding sponges. I wiped the stummel off with an alcohol dampened make-up pad and let it dry. The stummel was then coated with Before and After Restoration Balm and allowed to sit overnight.

In the morning the Restoration Balm was hand buffed from the stummel using the inside of an athletic sock. The terrycloth of the sock worked excess balm from the rustications of the carvings and left a very pretty shine on the stummel.

The stummel needed an equally attractive stem, so back to work. I wiped the excess mineral oil from the stem and began sanding with the series of sponges – 1000-3500. Between each sponge I would dip my finger in the mineral oil, rub the stem and wipe it dry with a paper towel. I would also wipe the sponge off on the denim to keep the sponges kind of clean.

After the sanding I started to micro-mesh the stem. Here I used the 4000-12000 micro-mesh pads in sequence. Between each pad I applied a drop of Obsidian Oil. The oil was rubbed in with my finger and wiped away with a paper towel.

The final steps in polishing the stem were done with Before and After Fine and Extra Fine Polish. The polish was applied by finger tip and hand rubbed with a soft cotton rag. Fine Polish followed by the Extra Fine Polish.

The final touch was the application of several coats of carnauba wax with the buffer. I tried to only apply the wax to the high area but gave up on that. I used the edges of the buffing wheel to work the wax into the carvings. When I was finished I replaced the waxing wheel with a clean flannel wheel. I used this wheel without any wax and used the corner edge of the wheel to get into the carving grooves. My thought was to melt and absorb as much of the wax from the grooves as possible while still leaving a thin coating to protect the briar. It looked good.

Overall I was very pleased at how well this Kaywoodie turned out. These were fun pipes to work on and their size makes you feel like you have accomplished a real feat. The briar cleaned up beautifully and the stem again shines like new vulcanite should. As for the dimensions of this pipe, as I said it is large, the dimensions are as follows:

Weight: 3.12 ounce/ 88.45 g.

Length: 6.42 in./ 163.07 mm.

Bowl Height: 2.18 in./ 55.37 mm.

Chamber Depth: 1.85 in./ 46.99 mm.

Chamber Diameter: 0.84 in./ 21.34 mm.

Outside Dimension (side-side): 1.60 in./ 40.64 mm.

Outside Dimension (front-back): 1.91 in./ 48.51 mm.

These are not pipes that you can clench while raking leaves or shoveling snow. This pipe demands you attention. I am sure the reward for such demands is a very nice cool smoke. I do hope that you have found this to be useful and entertaining. If you enjoy this sort of thing, please click the like and subscribe. I thank you for reading the ramblings of an old pipe lover.

Below are some photos of the Kaywoodie HandMade Saddle Stem.

Well, I’ll be darned. I didn’t forget.
A Kaywoodie HandMade tapered stem Restoration, dé·jà vu

February 28th, 2024

Photographed and written by

John M. Young

I know what you are thinking: “Dang Young, you must be getting old and didn’t realize that you already posted that restoration.” And I reply: “Hah, this is a different one. This one has a screw-in tenon and a pre-1955 logo.” You are correct though, I am getting old. I came across two more of these Kaywoodie Hand Mades the other day and settled on a price with the seller. This one has a lovely tapered stem while the other one has a saddle stem. These pipes make me think of the word “lumber” when I handle them. They are large. Both over 2.5 ounces (71 g). Not clenchers but, I am sure they will be cool smokers.

I am going to use the historical information from the previous Kaywoodie HandMade restoration. I linked that blog as well, for those who would like to read it.

“Kaywoodie name first appearing in February of 1919.” (Kaywoodie History – Greywoodie LLC) The history of Kaywoodie pipes is fortunately well documented thus, allowing rather precise dates for a Kaywoodie collector to declare the provenance of their charges. The above pictured Kaywoodie is stamped HANDMADE over KAYWOODIE (left) and IMPORTED BRIAR (right). No shape number is present.

Using this information and referring to the Kaywoodie Collectors’ Guide listed on pipedia.org I found that these pipes were made during the following years:

“Handmade-Oversize-Carved 1947-1955 on and off” (https://pipedia.org/images/3/3d/Kaywoodie_Pipe_Names.pdf) and that

“The Oversize Kaywoodies were, as the name implies, “Giants”. Lowndes notes that these pipes were stamped simply, “Hand-Made”. The pipes were all roughly “bulldogish” in appearance and were available in the following styles and grades7 : • Hand-carved “Colossus” ($10) • Walnut finish, banded “Hercules” ($20) • Hand-carved “John Henry” ($10) • Virgin finish, specimen grain “Paul Bunyan” • ($25)Virgin finish, banded specimen grain “Goliath” • ($25)Walnut finish “Atlas” • ($20)Hand-carved, Meerschaum-Inlaid “Samson” ($15)” (Kaywoodie Collector’s Guide – p10.pdf)

Looking into the stampings, I went to piphil.eu for confirmation. ThereI was able to find an exact match of this pipe’s stampings.

(Kaywoodie series from L to Z — Pipes : Logos & Markings (pipephil.eu))

Well, that was easy. This large Kaywoodie Hand Made, though not very “bulldogish” was most likely made between 1947 and 1955 at the West New York, New Jersey factory. If you would like to see the 1947 Kaywoodie catalog here is a link: Kaywoodie_1947.pdf (pipedia.org). It is a fascinating read with great old marketing photos and illustrations. Just out of curiosity I wondered what $10 in 1947 was equivalent to today. According to a bis.gov inflation calculator it is $131.09 (Using Dec. 1947 and Dec. 2023)(CPI Inflation Calculator (bls.gov)). I highly recommend reading the above links for further Kaywoodie history.

With that perfect example of a generation-X lazy re-use of a previous blog history it is time to get to the restoration. Here is what the Kaywoodie HandMade taper stem (that is what I’m calling it) looked like upon arrival.

This looked like a normal restoration. The main tasks to be completed should be: Reaming the tobacco chamber, cleaning out the airway, cleaning and removing any finish from the stummel, removing the oxidation, and restoration of the stem, wax and polish. It always sounds easier than it actually turns out to be but I am an optimist.

I started with a clean denim piece for the work surface and started working on the stem.

I began with the airway within the stem. I am not a big fan of stingers especially, stingers that don’t come apart. At least with those you can slide out the funky shaped end-piece and run a pipe cleaner through a fairly open hole. Kaywoodies on the other hand, not so much. I was able to get a bristle pipe cleaner dipped in alcohol from the button end down into the stem. Fortunately the stem was not too dirty. Thank you, previous owner. A couple pipe cleaners later and the stem was clean.

Nex, I rubbed the surface with 0000 steel wool then dipped the steel wool into 99% isopropyl alcohol and cleaned up the stinger. After the steel wool I thought that I would not need to give this stem a soak in the Before and After Deoxidizing solution.

The stinger cleaned up nicely and the oxidation on the stem looked like all it needed was Soft Scrub on a make-up pad. Well, several applications of Soft Scrub, that is.

After a mineral oil rub the stem was looking much better. I set it aside to soak-in some oil and started to work on the stummel.

I gathered the reaming crew: The pipNet with the #2 and #3 bladed, Smokingpipes Low Country knife, General triangular scraper, 220 sandpaper wrapped wood dowel and the 320 sandpaper wrapped Sharpie marker.

With the crew all ready I started with the PipNet with #2 blades attached. It was far smaller than the tobacco chamber but working in steps is easier that taking a large step.

It reminded me of the old saying, “How do you eat an elephant?”. “One bite at a time.” The #3 blades cleaned up the chamber most of the way and required little scraping with the knife or scraper.

The chamber was sanded to bare briar with the 220 sandpaper and finished with the 320 sandpaper. There was a strange groove cut into the chamber from nearly the top to the bottom. The groove was about 1-2 mm wide and not a mm deep. I tried to sand it smooth without getting the chamber out of round.

I normally would have addressed the rim at this time but the rim had fine rustications and a smooth surface immediately out from the chamber. I did not want to change the rustication so opted to try to remove the lava with the Murphy’s Oil Soap scrubbing. I did want to get some idea for how fouled the airway of the shank was. I moistened several cotton swabs with alcohol and tried scrubbing the shank. They came back very darkly stained with tar and yuck (the technical term for black tar like smoking residue). That told me that the shank cleaning would be a difficult one. The Kaywoodie mortise being aluminum meant that it was difficult to do any scraping of the airway with a dental scraper.

I took the stummel to the sink for scrubbing. At the sink I used Murphy’s Oil Soap undiluted and scrubbed the stummel with a medium bristle toothbrush. A surprising amount of old dirt and grime came off in the scrub.

The rim was scrubbed with the toothbrush initially then I graduated up to a brass brush to remove the lava without damaging the rustication. The stummel was rinsed with warm water and dried with a cotton dish towel. I then poured about 5 ml of 95% ethyl alcohol into the bowl. I let this flow into the shank without pouring it out. I then scrubbed the airway using a nylon shank brush allowing the alcohol to soften and dissolve the accumulated yuck. This was then poured into a medicine cup. The results were very dark and indicated that the shank was full of yuck.

I returned to the workbench to do what scraping I could with the dental scraper. Anything I could get out with the scraper was worth several alcohol/shank brush scrubs.

The scraping alternated with alcohol and nylon brush scrubbing. An abbreviation that comes to mind is TMTC, meaning too many to count. TMTC later the cotton swabs were finally yielding less and less yuck.

With the shank finally cleaned out I returned my attention to the exterior of the stummel. I wiped the exterior with a make-up pad wetted with 95% ethyl alcohol. The briar did not appear to have been stained and not finished. I was hoping that it was just wax and grime that would be removed with the pad.

The alcohol pad came back with what looked like some sort of finish or wax, mostly from the carved areas. I decided to use an alcohol dipped brass brush to scrub the carved areas more thoroughly.

This resulted in removing much more, whatever it was that was, being removed. The stummel looked much cleaner. The only sanding that I did to the stummel was a slight beveling of the rim around the tobacco chamber to eliminate some of the charred wood from lighting the pipe. Since there wasn’t really anything to sand or micro-mesh on the stummel I gave it a coating of Before and After Restoration Balm worked into the rustications with a baby toothbrush and set it aside.

The stem had soaked up a bit of the mineral oil. I started with the 400 and 600 sanding sponges. I wanted to see if the tooth dents were bad enough to fill or if they could just be sanded.

The dents on top were minimal but the both would require filling with black cyanoacrylate (CA, super glue). I placed a small drop of the black CA on the dent filling it. I then spritzed the drop with a CA drying accelerator. This dries the CA almost immediately. I then filed the drop smooth. A second layer of CA was then spread over the entire area from the button back up the stem for about 1/2 inch (1 cm).

This was then smoothed with a flat needle file, followed by the 400 and 600 sanding sponges. The wider area helps blend the filled dents better than just having CA spots on the vulcanite.

I admit to doing a poor job at photo-documenting the process with step by step photos of both top and bottom. The results look good though. Next was sanding the stem with the full series of sanding sponges from 1000-3500. Between each sponge I applied a finger dipped in mineral oil to the stem then wiped it off with a paper towel.

After the sanding sponges I used micro-mesh pads 4000-12000 to further polish the stem. Between each of these pads I applied a drop of Obsidian Oil, rubbed it in with a finger and wiped the stem off with a paper towel.

The final polishing was done with Before and After Fine followed by their Extra Fine Polishes. These were applied with a finger and rubbed with a soft cotton cloth.

I had allowed the Before and After Restoration Balm to dry overnight on the stummel. It had formed a slightly tacky textured finish that I hand buffed off with the inside of an athletic sock. I do love the way the terry-cloth of a sock removes the excess balm.

The pipe was reassembled and taken to the buff for several coats of carnauba wax. I tried to apply very light coats of wax to the rusticated carved surfaces using the edges of the buffing wheel to work the wax into the carvings. It seemed to work well. After the application of was I replaced the waxing wheel with a clean buffing wheel and went over the carving again hoping to draw out excess wax with the clean buffing flannel. The waxing wheel was placed back on and I applied a final coating of carnaube to the smooth surfaces carefully avoiding the carvings.

Overall this Kaywoodie HandMade tapered stem turned out very well. It feels very good, substantial but good in hand. My fingers seem to line up nicely with the carvings making it quite comfortable to hold. This is probably good because clenching this pipe would be difficult with it’s 2.52 ounce weight. The other dimensions are as follows:

Length: 6.16 in./

Bowl Height: 2.20 in./ 156.46 mm

Chamber Depth: 1.96 in./ 49.78 mm

Chamber Diameter: 0.85 in./ 21.59 mm

Outside Dimension (side-side): 1.67 in./ 42.42 mm

Outside Dimension (front-back): 1.89 in./ 48.01 mm

Yes, she is a big girl, some might even refer to this pipe as lumber. Were I a betting man, I would wager that she smokes very coolly. I do hope that you have found this to be useful and entertaining. If you enjoy this sort of thing, please click the like and subscribe. I thank you for reading the ramblings of an old pipe lover.

Below are some of the finished photos of the Kaywoodie HandMade taper stem.
A Kaywoodie HandMade Restoration

February 14th, 2024

Photographed and written by

John M. Young

If I were a betting man, I believe it would be a fairly safe bet to say that many pipe smokers had either a Dr Graybow or a Kaywoodie as one of their first pipes. Kaywoodie has a long and colorful history dating back to their origins, “Kaywoodie name first appearing in February of 1919.” (Kaywoodie History – Greywoodie LLC) The history of Kaywoodie pipes is fortunately well documented thus, allowing rather precise dates for a Kaywoodie collector to declare the provenance of their charges. The above pictured Kaywoodie is stamped HANDMADE over KAYWOODIE (left) and IMPORTED BRIAR (right). No shape number is present.

Using this information and referring to the Kaywoodie Collectors’ Guide listed on pipedia.org I found that these pipes were made during the following years:

“Handmade-Oversize-Carved 1947-1955 on and off” (https://pipedia.org/images/3/3d/Kaywoodie_Pipe_Names.pdf) and that

“The Oversize Kaywoodies were, as the name implies, “Giants”. Lowndes notes that these pipes were stamped simply, “Hand-Made”. The pipes were all roughly “bulldogish” in appearance and were available in the following styles and grades7 : • Hand-carved “Colossus” ($10) • Walnut finish, banded “Hercules” ($20) • Hand-carved “John Henry” ($10) • Virgin finish, specimen grain “Paul Bunyan” • ($25)Virgin finish, banded specimen grain “Goliath” • ($25)Walnut finish “Atlas” • ($20)Hand-carved, Meerschaum-Inlaid “Samson” ($15)” (Kaywoodie Collector’s Guide – p10.pdf)

Looking into the stampings, I went to piphil.eu for confirmation. ThereI was able to find an exact match of this pipe’s stampings.

(Kaywoodie series from L to Z — Pipes : Logos & Markings (pipephil.eu))

Well, that was easy. This large Kaywoodie Hand Made, though not very “bulldogish” was most likely made between 1947 and 1955 at the West New York, New Jersey factory. If you would like to see the 1947 Kaywoodie catalog here is a link: Kaywoodie_1947.pdf (pipedia.org). It is a fascinating read with great old marketing photos and illustrations. Just out of curiosity I wondered what $10 in 1947 was equivalent to today. According to a bis.gov inflation calculator it is $131.09 (Using Dec. 1947 and Dec. 2023)(CPI Inflation Calculator (bls.gov)). I highly recommend reading the above links for further Kaywoodie history.

Before we get to the restoration let’s take a look at how the pipe appeared before I did any work to it and compare it to a more normal size Kaywoodie.

Just kidding. That is actually a mini pipe. Here is a real comparison using a Kaywoodie author. And yes, the Hand Made in those last two photos is the finished version.

Now we can do the restoration part. Normally I begin with a clean denim piece to work on then get out the white plastic reaming surface and do the reaming. This time I did start with the denim but started scraping the shank and the tenon on the white plastic rather than reaming.

As you can see, quite a bit of tar/smoking residue was removed. After this I addressed the tobacco chamber. The tools were the PipNet with #3 blades, Smokingpipes knife, General triangular scraper, 220 sandpaper wrapped around a wood dowel and 320 sandpaper wrapped around a Sharpie marker.

The PipNet did the majority of the work. Although the chamber did not look heavily caked the bowl was so large that the cake that was there left a large pile. After the PipNet the knife and scraper were used followed by the sanding with 220 then 320 to get to bare briar. The tobacco chamber looked good and free of any heat damage.

The next task was to clean the exterior of the stummel. I took it to the sink and scrubbed the stummel with undiluted Murphy’s Oil Soap and a medium bristle toothbrush. This was repeated two times. I spent extra time scrubbing the rim and the rusticated surfaces couldn’t be scraped to

free them from lava. I was not happy with the way the lava was being removed with the toothbrush so I used a brass brush to further scrub the rim. The Murphy’s was rinsed off with warm water and the stummel dried with a cotton dish towel. I then poured about 5 ml of 95% ethyl alcohol into the bowl. I allowed the alcohol to flow into the shank but not pour out. I then used a nylon shank brush to scrub the airway of the shank. After the scrubbing I poured the alcohol into a medicine cup. The alcohol was dark brown. I applied a drop of Dawn dish soap to the shank brush and scrubbed the airway again with soap and water. The soap lather was dark gray. The soap was rinsed and scrubbed while rinsing. to rid the airway of all the soap. Fresh alcohol was poured into the bowl and I again scrubbed the airway with the shank brush and alcohol. This time the alcohol was much lighter when poured into the medicine cup.

I returned to the workbench. I wetted a make-up pad with 95% ethyl alcohol and wiped the exterior of the stummel. The carved groves still looked like they had some of the years of accumulated dirt and grime ground into them. I then dipped a baby toothbrush into the alcohol and scrubbed the stummel with that. The carvings had ridges that ran perpendicular to the grooves. I matched the scrubbing of the toothbrush to the ridges and

scrubbed them with alcohol. After the scrub I again wiped the surface with an alcohol wetting make-up pad. The stummel exterior was cleaned.

The exterior of the stummel was looking good. Now to deal with the airway. I was hoping that the scraping, alcohol scrub and the soap scrub would make cleaning the airway a bit easier. I was right, it did. Now, that is not to say that I didn’t have to do a couple more alcohol nylon brush scrubs. I did and many cotton swabs as well but all the scraping and previous scrubbing had made my life a bit easier. Eventually the airway was clean.

I was pleased at how stummel had cleaned-up with the accumulated dirt gone. The rim still did not look good. Below are photos of the scrubbed stummel and rim.

I was not pleased with the charring of the rim. I would normally rub Vaseline on the rim and scrape this with a sharp knife to remove the charred briar. The rustication prevented this. New plan, soak the rim in Murphy’s oil soap for an hour then try scrubbing it again. I had no idea if it would work but I thought I remembered reading about a German Facebook buddy doing it with a pipe. I found a wider medicine cup and poured in a few millimeters of Murphy’s Oil Soap.

While waiting for the Murphy’s to do or not do something, I started the initial sanding of the stem. I used the 400, 600 and 1000 sanding sponges to remove the tooth chatter, scratches and oxidation from the stem. I then used Soft Scrub on a make-up pad to vigorously rub the stem. This worked brilliantly. The Soft Scrub removed all signs of oxidation and left a beautifully black stem behind. The stem was then coated with mineral oil and let to sit and absorb oil.

Although it had only been about 15 minutes, I couldn’t wait to see if the Murphy’s was doing anything to the charred briar. I lifted it up and used the baby toothbrush to scrub the rim. The soap darkened with charred wood. Wow, this is actually doing something! Sascha Mertens, the Facebook pipe restoration buddy from Germany, comes through again. Thank you Sascha!

I placed the stummel back into the soap and waited another 15 minutes. Fortunately Netflix and Lorenzo Medici kept me from tampering with the stummel. 15 minutes and another baby toothbrush scrub and more of the char seemed to be gone. Well let’s see what evil plots Lorenzo can nullify in a half hour. 30 minutes later and saving the Medici Bank from usurpers, miscreants and maybe some alien vampires at least 10 times, Lorenzo and I were victorious. He, at saving the bank and Medici family and me at removing most of the char from the Kaywoodie.

Okay, it wasn’t all gone but a little sanding with a wooden ball and 220 to give the rim a bevel and…

Who knows what kind of magic will happen?

I could live with that.

The sanding of the stummel went fairly quickly as I only had to work on the smooth sections. I used the 400 and 600 sanding sponges lightly and wiped with an alcohol wetted make-up pad. I was looking for sand pits that might require filling. I found a few all in one smooth section. Unfortunately I did not photograph this step but, you can see the fills as dark spots on these before and after shots of the right side. The pits were filled using

Cyanoacrylate (CA, super glue) dabbed into the pit. I then placed a pinch of briar dust on top of the CA and pressed hard with my fingertip. The CA and briar dust set-up almost immediately. I then used a small flat needle file to smooth the fill and finished it with the 400 and 600 sanding sponge. I continued with the series of 1000-3500 sanding sponges. Between each sponge I wiped the stummel with an alcohol wetted make-up pad.

Once the stummel was sanded I moved on to micro-mesh the stummel. The 4000-12000 micro-mesh pads were used. Again, as with the sanding sponges, I wiped the stummel with an alcohol wetted make-up pad between pads.

At this point I applied a coating of Before and After Restoration Balm to the briar. I world the balm into the rustications with a baby toothbrush. The balm was allowed to sit for an hour.

After an hour, I applied additional Restoration Balm to areas of the stummel that appeared to have soaked-up the Restoration Balm and now looked dry. This was mainly on the rim. An additional 20 minutes was given to the stummel.

After 20 minutes, the remaining Restoration Balm was wiped away with the inside of an athletic sock. The terry cloth material was great at getting into the rough surfaces and wiping away the excess balm.

Back to the stem. I wanted the stem/shank joint to be nice and tight with no rounding of the edges. To manage this I wanted to sand the stem in place with the shank. I had avoided sanding the edge of the shank while sanding the stummel but that cannot be done with a stem and still look finished. I needed to protect the shank so wrapping it with painters tape was in order.

I worked the stem with the 1000-3500 sanding sponges in sequence. Between each sponge I rubbed the stem with mineral oil on my finger and wiped it with a paper towel. When finished with the sanding sponges I used the 4000-12000 micro-mesh pads in sequence. Between each pad I rubbed in a drop of Obsidian Oil with my finger and wiped it with a paper towel. The final stem polishing was done with Before and After Fine Polish. This was applied with my finger and rubbed with a soft cotton rag. The Fine Polish was followed by Before and After Extra Fine Polish applied and rubbed the same way.

The last step to this restoration was to apply a couple of coats of carnauba wax using the buffer. I tried to only apply the carnauba to the flat surfaces. This meant that I could not apply the normal amount of pressure with the pipe to the buffing wheel. I did not want to get carnauba wax embedded into all of the grooves of the carvings. This made me go much slower and more carefully. It worked and looked great. I still felt like the grooves needed some kind of wood sealer or protector. I opted to use Renaissance Micro-crystalline Wax Polish. This is a wax that can leave white spots if it is allowed to

dry too thickly. I applied it with my finger tip, working it into the coarse grooves. While it was drying I buffed it with a shoe shine brush. The hairs of the brush smoothed and evened out the wax as it was drying. Like it says on the label “Apply sparingly with a soft cloth and buff gently. Dries hard instantly. Resists liquids spillage. Does not show finger marks”. I wanted the “dried hard” and “resists liquids” features. I also love the solvent based smell of it. When completely dry the smell is gone. I hand buffed the completely dried pipe with a microfiber polishing cloth.

I am very pleased at how well this Kaywoodie Hand Made pipe turned out. It feels good in hand with the grooves being smooth and comfortable. The smooth surfaces, separated by the carved grooves, come together nicely towards the shank. The briar grain, though not distinctive, is attractive. I am impressed with how well the stem polished-up it’s glossy black contrasts the medium browns of the stummel beautifully. This is a very large pipe weighing 2.7 ounces (76,5 g). It’s length is 6 in. (15.2mm), bowl height: 2.38 in. (60mm), chamber depth: 2 in. (50.8 mm), chamber diameter:.875 in. (22.2 mm), outside diameter (side-side): 1.63 in (41.4 mm), outside diameter (front-back): 1.75 in. (44.5mm).

I do hope that you have found something here useful. If you like this sort of thing, please click the like and subscribe buttons. I thank you for reading the ramblings of an old pipe lover.

Below are some photos of the finished Kaywoodie Hand Made.